Slacky-DIY TS0201-z-SlD


Model	TS0201-z-SlD
Vendor	Slacky-DIY
Description	Tuya temperature and humidity sensor with custom Firmware
Exposes	battery, voltage, temperature, humidity, temperature_offset, humidity_offset, read_interval, enabling_temperature_control, low_temperature, high_temperature, temperature_actions, enabling_humidity_control, low_humidity, high_humidity, humidity_actions
Picture

Original project description

OTA updates

This device supports OTA updates, for more information see OTA updates.

Options

How to use device type specific configuration

temperature_calibration: Calibrates the temperature value (absolute offset), takes into effect on next report of device. The value must be a number.
temperature_precision: Number of digits after decimal point for temperature, takes into effect on next report of device. This option can only decrease the precision, not increase it. The value must be a number with a minimum value of 0 and with a maximum value of 3
humidity_calibration: Calibrates the humidity value (absolute offset), takes into effect on next report of device. The value must be a number.
humidity_precision: Number of digits after decimal point for humidity, takes into effect on next report of device. This option can only decrease the precision, not increase it. The value must be a number with a minimum value of 0 and with a maximum value of 3

Remaining battery in %. Value can be found in the published state on the battery property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"battery": ""}. It's not possible to write (/set) this value. The minimal value is 0 and the maximum value is 100. The unit of this value is %.

Voltage (numeric)

Reported battery voltage in millivolts. Value can be found in the published state on the voltage property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"voltage": ""}. It's not possible to write (/set) this value. The unit of this value is mV.

Temperature (numeric)

Measured temperature value. Value can be found in the published state on the temperature property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"temperature": ""}. It's not possible to write (/set) this value. The unit of this value is °C.

Humidity (numeric)

Measured relative humidity. Value can be found in the published state on the humidity property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"humidity": ""}. It's not possible to write (/set) this value. The unit of this value is %.

Temperature offset (numeric)

Offset to add/subtract to the inside temperature. Value can be found in the published state on the temperature_offset property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"temperature_offset": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"temperature_offset": NEW_VALUE}. The minimal value is -5 and the maximum value is 5. The unit of this value is °C.

Humidity offset (numeric)

Offset to add/subtract to the inside temperature. Value can be found in the published state on the humidity_offset property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"humidity_offset": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"humidity_offset": NEW_VALUE}. The minimal value is -10 and the maximum value is 10. The unit of this value is %.

Read interval (numeric)

Sensors reading period. Value can be found in the published state on the read_interval property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"read_interval": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"read_interval": NEW_VALUE}. The minimal value is 15 and the maximum value is 600. The unit of this value is Sec.

Enabling temperature control (binary)

Enables/disables Tempearure control. Value can be found in the published state on the enabling_temperature_control property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"enabling_temperature_control": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"enabling_temperature_control": NEW_VALUE}. If value equals ON enabling temperature control is ON, if OFF OFF.

Low temperature (numeric)

Temperature low turn-off limit. Value can be found in the published state on the low_temperature property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"low_temperature": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"low_temperature": NEW_VALUE}. The minimal value is -40 and the maximum value is 125. The unit of this value is °C.

High temperature (numeric)

Temperature high turn-on limit. Value can be found in the published state on the high_temperature property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"high_temperature": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"high_temperature": NEW_VALUE}. The minimal value is -40 and the maximum value is 125. The unit of this value is °C.

Temperature actions (enum, 1 endpoint)

Heat or cool. Value can be found in the published state on the temperature_actions_1 property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"temperature_actions_1": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"temperature_actions_1": NEW_VALUE}. The possible values are: heat, cool.

Enabling humidity control (binary)

Enables/disables Humidity control. Value can be found in the published state on the enabling_humidity_control property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"enabling_humidity_control": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"enabling_humidity_control": NEW_VALUE}. If value equals ON enabling humidity control is ON, if OFF OFF.

Low humidity (numeric)

Humidity low turn-off limit. Value can be found in the published state on the low_humidity property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"low_humidity": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"low_humidity": NEW_VALUE}. The minimal value is 1 and the maximum value is 100. The unit of this value is %.

High humidity (numeric)

Humidity high turn-on limit. Value can be found in the published state on the high_humidity property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"high_humidity": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"high_humidity": NEW_VALUE}. The minimal value is 1 and the maximum value is 100. The unit of this value is %.

Humidity actions (enum, 2 endpoint)

Wet or dry. Value can be found in the published state on the humidity_actions_2 property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"humidity_actions_2": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"humidity_actions_2": NEW_VALUE}. The possible values are: wet, dry.