Ubisys S1-R


Model	S1-R
Vendor	Ubisys
Description	Power switch S1-R
Exposes	identify, switch (state), power_on_behavior, power, energy, action
Picture

OTA updates

This device supports OTA updates, for more information see OTA updates.

Options

How to use device type specific configuration

measurement_poll_interval: This device does not support reporting electric measurements so it is polled instead. The default poll interval is 60 seconds, set to -1 to disable. The value must be a number with a minimum value of -1
power_calibration: Calibrates the power value (percentual offset), takes into effect on next report of device. The value must be a number.
power_precision: Number of digits after decimal point for power, takes into effect on next report of device. This option can only decrease the precision, not increase it. The value must be a number with a minimum value of 0 and with a with a maximum value of 3
energy_calibration: Calibrates the energy value (percentual offset), takes into effect on next report of device. The value must be a number.
energy_precision: Number of digits after decimal point for energy, takes into effect on next report of device. This option can only decrease the precision, not increase it. The value must be a number with a minimum value of 0 and with a with a maximum value of 3
identify_timeout: Sets the duration of the identification procedure in seconds (i.e., how long the device would flash).The value ranges from 1 to 30 seconds (default: 3). The value must be a number with a minimum value of 1 and with a with a maximum value of 30
state_action: State actions will also be published as 'action' when true (default false). The value must be true or false
simulated_brightness: Simulate a brightness value. If this device provides a brightness_move_up or brightness_move_down action it is possible to specify the update interval and delta. The action_brightness_delta indicates the delta for each interval. Example:

simulated_brightness:
  delta: 20 # delta per interval, default = 20
  interval: 200 # interval in milliseconds, default = 200

Initiate device identification. Value will not be published in the state. It's not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"identify": NEW_VALUE}. The possible values are: identify.

Switch

The current state of this switch is in the published state under the state property (value is ON or OFF). To control this switch publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"state": "ON"}, {"state": "OFF"} or {"state": "TOGGLE"}. To read the current state of this switch publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"state": ""}.

On with timed off

When setting the state to ON, it might be possible to specify an automatic shutoff after a certain amount of time. To do this add an additional property on_time to the payload which is the time in seconds the state should remain on. Additionally an off_wait_time property can be added to the payload to specify the cooldown time in seconds when the switch will not answer to other on with timed off commands. Support depends on the switch firmware. Some devices might require both on_time and off_wait_time to work Examples : {"state" : "ON", "on_time": 300}, {"state" : "ON", "on_time": 300, "off_wait_time": 120}.

Power-on behavior (enum)

Controls the behavior when the device is powered on after power loss. Value can be found in the published state on the power_on_behavior property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"power_on_behavior": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"power_on_behavior": NEW_VALUE}. The possible values are: off, on, toggle, previous.

Power (numeric)

Instantaneous measured power. Value can be found in the published state on the power property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"power": ""}. It's not possible to write (/set) this value. The unit of this value is W.

Energy (numeric)

Sum of consumed energy. Value can be found in the published state on the energy property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"energy": ""}. It's not possible to write (/set) this value. The unit of this value is kWh.

Action (enum)

Triggered action (e.g. a button click). Value can be found in the published state on the action property. It's not possible to read (/get) or write (/set) this value. The possible values are: on_2, on_3, off_2, off_3, toggle_2, toggle_3, brightness_move_to_level_2, brightness_move_to_level_3, brightness_move_up_2, brightness_move_up_3, brightness_move_down_2, brightness_move_down_3, brightness_step_up_2, brightness_step_up_3, brightness_step_down_2, brightness_step_down_3, brightness_stop_2, brightness_stop_3, color_temperature_move_stop_2, color_temperature_move_stop_3, color_temperature_move_up_2, color_temperature_move_up_3, color_temperature_move_down_2, color_temperature_move_down_3, color_temperature_step_up_2, color_temperature_step_up_3, color_temperature_step_down_2, color_temperature_step_down_3, enhanced_move_to_hue_and_saturation_2, enhanced_move_to_hue_and_saturation_3, move_to_hue_and_saturation_2, move_to_hue_and_saturation_3, color_hue_step_up_2, color_hue_step_up_3, color_hue_step_down_2, color_hue_step_down_3, color_saturation_step_up_2, color_saturation_step_up_3, color_saturation_step_down_2, color_saturation_step_down_3, color_loop_set_2, color_loop_set_3, color_temperature_move_2, color_temperature_move_3, color_move_2, color_move_3, hue_move_2, hue_move_3, hue_stop_2, hue_stop_3, move_to_saturation_2, move_to_saturation_3, move_to_hue_2, move_to_hue_3.