Sinopé DM2500ZB

ModelDM2500ZB
VendorSinopé
DescriptionZigbee smart dimmer
Exposeslight (state, brightness), led_intensity_on, led_intensity_off, minimum_brightness, led_color_on, led_color_off, linkquality
PictureSinopé DM2500ZB

Options

How to use device type specific configuration

  • transition: Controls the transition time (in seconds) of on/off, brightness, color temperature (if applicable) and color (if applicable) changes. Defaults to 0 (no transition). The value must be a number with a minimum value of 0

  • power_calibration: Calibrates the power value (percentual offset), takes into effect on next report of device. The value must be a number.

  • power_precision: Number of digits after decimal point for power, takes into effect on next report of device. The value must be a number with a minimum value of 0 and with a with a maximum value of 3

  • current_calibration: Calibrates the current value (percentual offset), takes into effect on next report of device. The value must be a number.

  • current_precision: Number of digits after decimal point for current, takes into effect on next report of device. The value must be a number with a minimum value of 0 and with a with a maximum value of 3

  • voltage_calibration: Calibrates the voltage value (percentual offset), takes into effect on next report of device. The value must be a number.

  • voltage_precision: Number of digits after decimal point for voltage, takes into effect on next report of device. The value must be a number with a minimum value of 0 and with a with a maximum value of 3

Exposes

Light

This light supports the following features: state, brightness.

  • state: To control the state publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"state": "ON"}, {"state": "OFF"} or {"state": "TOGGLE"}. To read the state send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"state": ""}.
  • brightness: To control the brightness publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"brightness": VALUE} where VALUE is a number between 0 and 254. To read the brightness send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"brightness": ""}.

Led_intensity_on (numeric)

Control status LED when load ON. Value will not be published in the state. It's not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"led_intensity_on": NEW_VALUE}. The minimal value is 0 and the maximum value is 100.

Led_intensity_off (numeric)

Control status LED when load OFF. Value will not be published in the state. It's not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"led_intensity_off": NEW_VALUE}. The minimal value is 0 and the maximum value is 100.

Minimum_brightness (numeric)

Control minimum dimmer brightness. Value will not be published in the state. It's not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"minimum_brightness": NEW_VALUE}. The minimal value is 0 and the maximum value is 3000.

Led_color_on (composite)

Control status LED color when load ON. Can be set by publishing to zigbee2mqtt/FRIENDLY_NAME/set with payload {"led_color_on": {"r": VALUE, "g": VALUE, "b": VALUE}}

  • r (numeric)
  • g (numeric)
  • b (numeric)

Led_color_off (composite)

Control status LED color when load OFF. Can be set by publishing to zigbee2mqtt/FRIENDLY_NAME/set with payload {"led_color_off": {"r": VALUE, "g": VALUE, "b": VALUE}}

  • r (numeric)
  • g (numeric)
  • b (numeric)

Linkquality (numeric)

Link quality (signal strength). Value can be found in the published state on the linkquality property. It's not possible to read (/get) or write (/set) this value. The minimal value is 0 and the maximum value is 255. The unit of this value is lqi.