To contribute to this page, edit the following file

Moes ZLD-RCW #

Model ZLD-RCW
Vendor Moes
Description RGB+CCT Zigbee LED Controller
Exposes light (state, brightness, color_temp, color_temp_startup, color_xy), effect, do_not_disturb, color_power_on_behavior, linkquality
Picture Moes ZLD-RCW

Notes #

Device type specific configuration #

How to use device type specific configuration

Exposes #

Light #

This light supports the following features: state, brightness, color_temp, color_temp_startup, color_xy.

Transition #

For all of the above mentioned features it is possible to do a transition of the value over time. To do this add an additional property transition to the payload which is the transition time in seconds. Examples: {"brightness":156,"transition":3}, {"color_temp":241,"transition":1}.

Moving/stepping #

Instead of setting a value (e.g. brightness) directly it is also possible to:

The direction of move and step can be either up or down, provide a negative value to move/step down, a positive value to move/step up. To do this send a payload like below to zigbee2mqtt/FRIENDLY_NAME/set

NOTE: brightness move/step will stop at the minimum brightness and won’t turn on the light when it’s off. In this case use brightness_move_onoff/brightness_step_onoff

{
  "brightness_move": -40, // Starts moving brightness down at 40 units per second
  "brightness_move": 0, // Stop moving brightness
  "brightness_step": 40 // Increases brightness by 40
  "color_temp_move": 60, // Starts moving color temperature up at 60 units per second
  "color_temp_move": "stop", // Stop moving color temperature
  "color_temp_step": 99, // Increase color temperature by 99
}

Effect (enum) #

Triggers an effect on the light (e.g. make light blink for a few seconds). Value will not be published in the state. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"effect": NEW_VALUE}. The possible values are: blink, breathe, okay, channel_change, finish_effect, stop_effect.

Do_not_disturb (binary) #

Do not disturb mode. Value can be found in the published state on the do_not_disturb property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"do_not_disturb": NEW_VALUE}. If value equals true do_not_disturb is ON, if false OFF.

Color_power_on_behavior (enum) #

Power on behavior state. Value can be found in the published state on the color_power_on_behavior property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"color_power_on_behavior": NEW_VALUE}. The possible values are: initial, previous, cutomized.

Linkquality (numeric) #

Link quality (signal strength). Value can be found in the published state on the linkquality property. It’s not possible to read (/get) or write (/set) this value. The minimal value is 0 and the maximum value is 255. The unit of this value is lqi.

Manual Home Assistant configuration #

Although Home Assistant integration through MQTT discovery is preferred, manual integration is possible with the following configuration:

light:
  - platform: "mqtt"
    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
    availability_topic: "zigbee2mqtt/bridge/state"
    brightness: true
    schema: "json"
    command_topic: "zigbee2mqtt/<FRIENDLY_NAME>/set"
    brightness_scale: 254
    color_mode: true
    supported_color_modes: 
      - "xy"
      - "color_temp"
    max_mireds: 500
    min_mireds: 153
    effect: true
    effect_list: 
      - "blink"
      - "breathe"
      - "okay"
      - "channel_change"
      - "finish_effect"
      - "stop_effect"

switch:
  - platform: "mqtt"
    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
    availability_topic: "zigbee2mqtt/bridge/state"
    value_template: "{% if value_json.do_not_disturb %} true {% else %} false {% endif %}"
    payload_on: "true"
    payload_off: "false"
    command_topic: "zigbee2mqtt/<FRIENDLY_NAME>/set"
    command_topic_postfix: "do_not_disturb"

sensor:
  - platform: "mqtt"
    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
    availability_topic: "zigbee2mqtt/bridge/state"
    value_template: "{{ value_json.color_power_on_behavior }}"
    enabled_by_default: false
    icon: "mdi:palette"

select:
  - platform: "mqtt"
    state_topic: true
    availability_topic: "zigbee2mqtt/bridge/state"
    value_template: "{{ value_json.color_power_on_behavior }}"
    command_topic: "zigbee2mqtt/<FRIENDLY_NAME>/set"
    command_topic_postfix: "color_power_on_behavior"
    options: 
      - "initial"
      - "previous"
      - "cutomized"
    enabled_by_default: false
    icon: "mdi:palette"

sensor:
  - platform: "mqtt"
    state_topic: "zigbee2mqtt/<FRIENDLY_NAME>"
    availability_topic: "zigbee2mqtt/bridge/state"
    value_template: "{{ value_json.linkquality }}"
    unit_of_measurement: "lqi"
    enabled_by_default: false
    icon: "mdi:signal"
    state_class: "measurement"